JetCon 2401 Specifications

Overview Specifications Ordering Information Datasheet Power Plant Automation

Industrial Serial to Fiber Media Converter 3-in-1 RS232/422/485 to serial fiber media converter Easy mode change without resetting Supports Multi-mode 5KM, Single-mode 40KM PTP or SFR transmission mode for serial fiber ring communication Auto baud rate and direction control High level immunity with 15KV ESD protection Two-way 120 ohm line terminator Supports biasing resistor Dual modes for power input, AC 24V(12~32V)/ DC 24V(12~48V) -20~70°C operating temperature for hazardous environment applications (-40~70°C wide operating temperature available by request)

Technology
Standard	EIA/TIA-232 RS-232 (ITU-T v.28) EIA/TIA-422 RS-422 (ITU-T v.11) EIA/TIA-485 RS-485 (ISO/IEC8284)
Serial Interface	RS-232 2-wires,RS-422 4-wire, RS-485 2/4-wire
Architecture	PTP mode: Peer To Peer wiring with full or half duplex mode SFR mode: Serial Fiber Ring with half duplex mode
Interface
Number of Ports	1 x RS-232/RS-422/RS-485 serial port 1 x Fiber Transmit port, 1 x Fiber receive port
Connectors	Serial port: 7-pin removable terminal block Fiber port: 1 x Duplex ST Power input: 3-pin removable terminal block with earth ground
Transmit Baud Rate	300bps to 921.6Kbps
Link distance	RS-232: 50 feet RS-422: 4000 feet RS-485: 4000 feet Multi-mode fiber: 50/125um or 62.5/125um, max. distance 5KM Single-mode fiber: 8/125um, 9/125um max. distance 40KM
Serial signal	RS-232: TxD, RxD, Signal Ground. RS-422: TxD+, TxD-, RxD+, RxD-, Signal Ground RS-485 4 wires: TxD+, TxD-, RxD+, RxD-, Signal Ground. RS-485 2 wires: Data+, Data-, Signal Ground.
Fiber Transceiver	JetCon2401-m, Multi-mode: Distance:5KM @ 62.5/125um multi mode cable with 3dbm/km attenuation Wave-length: 820nm TX Power: -12dBm (Min) ~ -9dBm (Max) RX Sensitivity: -28dBm (Min) Link budget: 16dBm JetCon2401-s, Single-mode: Distance: 40KM@9/125um single mode cable with 0.35dbm/km attenuation Wave-length:1310nm TX Power: -9dBm (Min) ~-8dBm (Max) RX Sensitivity: -27dBm (Min) Link budget: 18dBm
Configuration DIP Switch	Switch 1 and 2: serial interface mode selection Switch 3: RX 120ohm terminator Disable (off)/Enable (on) Switch 4: TX 120ohm terminator Disable (off)/Enable (on) Switch 5: PTP mode (off) / SFR mode (on).
Diagnostic LED	Power LED: Power 1 (Green) TX (Green): Serial port is on transmitting data. RX (Yellow): Serial port is on receiving data. Ring mode (Green): Working on SFR (Serial Fiber Ring) mode.
Power Requirements
System Power	Positive or negative power system. DC 24V (12~48V) with reverse polarity protection. AC 24V (AC12~32V, 50/60Hz) Provides 0.65A over current protection
Power Consumption	1.5Watts @ 24V(Maximum)
Mechanical
Installation	DIN-Rail mount or desktop
Casing	IP-30 grade aluminum metal case
Dimensions	24.7mm(H) x 74mm (W) x 99mm (D) with DIN
Weight	0.24kg with package 0.135kg without package
Environmental
Operating Temperature	-20 ~ 70°C (JetCon 2401-mw/2401-sw -40~70°C)
Operating Humidity	5% ~ 95% (Non-condensing)
Storage Temperature	-40 ~ 80°C
Storage Humidity	5% ~ 95% (Non-condensing)
Regulatory Approvals
EMI	FCC Class B; CE/EN55022:2003,class B; CE/EN61000-3-2:2001 Harmonic Test CE/EN61000-3-3:1995 Flicker test
EMS	EN61000-4-2:1998, ESD Testing, Level 3 EN61000-4-3:1998, RS testing, Level 3 EN61000-4-4:1995, EFT testing, Level 3 EN61000-4-5:1995, Surge test, Level 3 EN61000-4-6:1996, CS testing, Level 3
Safety	CE/EN60950
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Warranty	5 Years