JetCon 2301 Specifications

Overview Specifications Ordering Information Datasheet

Fast Ethernet to Fiber Media Converter  One 10/100 TX port to One 100FX port media converter Supports Multi-Forwarding modes – Store and Forward, (Switching Converter) Modify Cut-through, Pure Converter and Converter with Auto Change modes Supports Auto MDI/MDI-X, Auto Negotiation Supports Multi-mode 2KM, Single-mode 30KM Extreme Low Data Forwarding Latency- 1.6 x 10-6 Sec Auto Link Loss Forwarding (LLF) for fault detection Fault Alert for port and power Redundant 10~60V DC Power inputs with DC polarity protection Supports AC 1.5KV Hi-Pot isolation protection EN 50121-3-2 Railway EMC compliance (applying) Operating temperature -25~75°C (-40~75°C wide operating temperature model available by request)

Technology
Standard	IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3u 100Base-FX IEEE 802.3x Flow Control and Back Pressure
Forwarding Technology	Supports 4 types of forwarding mode, store and forward, modify cut-through, pure converter and converter mode with auto negotiation. This feature is selected by DIP-switch.
Link Lose Forwarding	Supports Bi-directional Link Loss Forwarding function.
TX Auto Sensing/Forced	RJ-45 port supports auto-negotiation and forced mode – 10Mbps/Half Duplex.
Packet Length	64~1600Bytes @ Pure Converter mode.
Forwarding Latency	Store and Forward: 250uS Modify Cut-Through: 17uS Converter : 1.6uS
IEEE 802.3 flow control /back-pressure	Enabled by DIP Switch.
Event Alarm	Supports port link down and power event alarm relay output, controlled by DIP switch.
Digital Output	Dry Relay Output with 1A @24V DC ability
Interface
Number of Ports	Ethernet copper port: 1 10/100TX ports with Auto MDI/MDI-X, Auto Negotiation Fiber port: 1 100Mbps Fiber port, SC
Cables	RJ-45 Connector: 10Base-T: 2-pairs UTP/STP Cat-3,4 TIA/EIA 568-B cable, 100 meters 100Base-TX : 2/4 pairs UTP/STP Cat.5 TIA/EIA 568-B cable, 100 meters Fast Ethernet Fiber Transceiver: SC connector: supports multi-mode or single-mode optical fiber Multi-mode fiber: 50/125um or 62.5/125um, max. distance 2KM Single-mode fiber: 8/125um, 9/125um or 10/125 um, max distance 30KM
Fiber Transceiver	JetCon 2301-m: 2KM (Max.) Wave-length: 1310nm Min TX Power:-19dBm Max TX Power:-14dBm Min RX Sensitivity:-14dBm Max RX Sensitivity:-31dBm Link budget:12dBm JetCon 2301-s : 30KM (Max.) Wave-length:1310nm Max TX Power:-8dBm Min TX Power:-15dBm Max RX Sensitivity:-34dBm Min RX Sensitivity:-8dBm Link budget: 19dBm
Diagnostic LEDs	System Power (Green on) : Power 1 , 2 Relay Alarm: Active (Red) Link Loss Forwarding : Far end fault event occurred (Red on) Op. Mode: Convert (Green on) (Controlled by DIP Switch 4) Fiber Ethernet Port: Link/Activity (Green on/Blinking), Full Duplex/Collision (Yellow on/Yellow Blinking) Ethernet Port: Link/Activity (Green on/Blinking), Full Duplex/Collision (Yellow On/ Yellow Blinking)
DIP Switch	DIP Switch 1: LLF Enable/Disable, default disable (DIP 1 off) DIP Switch 2: TX port Auto-Negotiation (OFF)/10H (ON), default disable (DIP 2 off) DIP Switch 3 & 4: Forwarding Mode Selection, default store & forward mode (DIP 3,4 off) DIP Switch 5: Power Alarm, default disable (DIP 5 off) DIP Switch 6: Port Alarm, default disable (DIP 6 off) DIP Switch 7: Flow Control, default enable (DIP 7 off)
Power Connector	Removable Terminal Block
Digital Output	Removable Terminal Block
Power Requirements
Power Supply	DC 10~60V with polarity reverses correction. Supports Positive/Negative power system
Power Consumption	5 Watts / DC 48V
Mechanical
System Installation	DIN Rail installation
Enclosure protection	Ingress Protection code - 30
Dimensions	55 mm (W) x 120 mm (H) x 99mm (D)
Weight	0.49Kg w/o packing
Environmental
Operating Temperature	-25 ~ 75°C (JetCon 2301-w:-40 ~ 75°C)
Operating Humidity	5% ~ 95% (Non-condensing)
Storage Temperature	-40 ~ 75°C
Storage Humidity	5% ~ 95% (Non-condensing)
Hi-Pot	AC 1.5KV on port to port and port to power
EMC	Compliant with EN 50121-3-2 EMC
Regulatory Approvals
EMI	CE/EN 55022 class A, FCC Class A EN 61000-3-2:2006, EN 61000-3-3, EN 61000-6-4
EMS	CE/ EN 55024, EN 61000-6-2 IEC 61000-4-2,IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-8
Shock	IEC 60068-2-27
Free Fall	IEC 60068-2-32
Vibration	IEC 60068-2-6