JetCon 1302 Specifications
|
Overview
Specifications
Ordering Information
 Datasheet
|
Industrial 2-port Fast Ethernet to Fiber Media Converter
- Two 10/100 TX ports to One 100FX port media converter
- Supports 1.5KV Hi-PoT isolation protection
- Dual modes for power input, AC18-27V/DC18-32V
- Fault Relay Output for port alarm
- Compact Aluminum case with IP-31 grade protection
- -10~70°C operating temperature for hazardous environment applications
|
| Technology |
|
|
|
IEEE802.3 10Base-T,IEEE802.3u 100Base-TX
IEEE802.3u 100Base-FX,IEEE802.3x flow control
| |
|
|
|
Store and forward technology and with 3.2Gbps switch bandwidth | |
| Aggregate System Throughput | |
|
| Interface |
|
|
|
2 x 10/100 TX with Auto MDI/MDI-X, Auto-Negotiation functions
1 x 100Base-FX | |
|
|
|
10/100 Base-TX: RJ-45
100Base-FX: Duplex SC
Power / Relay: 4-pin terminal block | |
|
|
|
RJ-45 connector: supports CAT-3, CAT-4, CAT-5 unshielded twisted pair or shielded twisted pair cable. The link distance is maximum 100 metersSC connector: SC Connector:
Multi-mode fiber: 50/125um or 62.5/125um, max. distance 2KM
Single-mode fiber: 8/125um, 9/125um or 10/125 um, max. distance 30KM | |
|
|
|
JetCon1302-m, Multi-mode: 2KM max. distance
Wave-length: 1310nm
Min Tx Power:-19dBm
Max Tx Power:-14dBm
Min Rx Sensitivity:-30dBm
Link budget:11dBm
JetCon1302-s, Single-mode: 30KM max. distance
Wave-length:1310nm
Max Tx Power:-8dBm
Min Tx Power:-15dBm
Min Rx Sensitivity:-34dBm
Link budget:19dBm
| |
|
|
|
DIP 1~3: Enable or disable port link down
alarm for copper port 1/2, fiber port 3
On: Enable port link down alarm
Off: Disable port link down alarm | |
|
|
|
System: Power (green), Fault (red)
RJ-45 port: 100Mbps Link (green on)/Activity(green blinking)
10Mbps Link (yellow on)/Activity(yellow blinking)
Fiber port: Link/Activity(green) | |
| Power Requirements |
|
|
|
2 pins terminal block for power input DC 24V(18~32V)with reverse polarity protection AC 18~27V, 47~63Hz | |
|
|
|
| Mechanical |
|
|
|
|
|
|
IP-31 protection, aluminum case | |
|
|
|
111.8mm(H) x 30mm (W) x 98.2mm (D) ( with DIN rail clip)
111.8mm(H) x 30mm (W) x 89.4mm (D) ( without DIN rail clip)
| |
|
|
|
374g with package
292g without package | |
| Environmental |
|
|
|
|
|
|
0% to 95% (Non-condensing) | |
|
|
|
|
|
|
| Regulatory Approvals |
|
|
|
FCC Class A, CE/EN55022 Class A
| |
|
|
|
EN61000-4-2: 6KV Contact, 8KV Air, ESD contact indirect 6kvEN61000-4-3: 10V/m, 80 MHz - 1 GHz, AM 1 KHz, 80% modulation,10V/m, 0.9 - 1.8 GHz, FM 200 Hz, 50% modulation
EN61000-4-4: PWR Supply Lines:+/- 2KV,Communication Lines:+/- 2KV
EN61000-4-5: 2KV on power line (L-N), 4KV on power line (L-PE, N-PE), 1.2uS Tr/ 50uS Th.
EN61000-4-6: PWR Supply Lines:10 Vrms, 150 KHz - 80 MHz;AM 1 KHz,80% modulation; Communication Lines:10 Vrms, 150 KHz - 80 MHz;AM 1 KHz, 80% modulation;Relay:10 Vrms, 150 KHz - 80 MHz;AM 1 KHz, 80% modulation
EN61000-4-8: 50Hz ,3A/m
EN61000-4-11: 30% 10 ms, 60% 100 ms, > 95% 5000 ms
| |
|
|
|
|
|
|
IEC60068-2-27 shock: 50G, 11ms, 4G, +/- X, +/- Y, +/- Z | |
|
|
|
IEC60068-2-32 free fall:90 cm, 1 corner, 3 edges, 6 faces | |
|
|
|
IEC60068-2-6 vibration: 1 mm, 2 Hz - 13.2 Hz, 90 min.; 0.7g, 13.2 Hz - 100 Hz, 90 min.; 3.5 mm, 3 Hz - 9 Hz, 10 cycles, 1 octave/min.; 1G, 9 Hz - 150 Hz, 10 cycles, 1 octave/min | |
|
|
| 632,171 Hours, MIL-HDBK-217F GB standard | |
|
|
| |
